ref: 649e0914486b43f31c89f8d17efc16d9df120198
dir: /extras/mydriver/video/firmware.a/
STRING C
MACHINE MC68020
PRINT OFF
INCLUDE 'SlotEqu.a'
INCLUDE 'VideoEqu.a'
INCLUDE 'Traps.a'
INCLUDE 'SysEqu.a'
INCLUDE 'SysErr.a'
PRINT ON
VideoDeclROM MAIN
;========================================================================================
; General Directives
BLANKS ON
STRING ASIS
kCmndVideoSetIntEnbl EQU $0003
kCmndVideoClearInt EQU $0004
kCmndVideoStatus EQU $0005
kCmndVideoControl EQU $0006
;========================================================================================
; Local Vars, definitions, etc...
;========================================================================================
;This is device storage, a handle to which is stored in the dCtlStorage field of the DCE.
saveSQElPtr EQU 0 ; the SQ element pointer (for
; _SIRemove
dCtlSize EQU saveSQElPtr+4 ; size of the dCtlStorage
;========================================================================================
; Video Driver Header
;========================================================================================
VidDrvr
DC.W $4C00 ; ctl,status,needsLock
DC.W 0, 0, 0 ; not an ornament
;Entry point offset table
DC.W VideoOpen - VidDrvr ; open routine
DC.W VidDrvr - VidDrvr ; no prime
DC.W VideoCtl - VidDrvr ; control
DC.W VideoStatus - VidDrvr ; status
DC.W VideoClose - VidDrvr ; close
VideoTitle
STRING Pascal
DC.W '.Display_Video_Sample'
STRING ASIS
ALIGN 2 ; make sure we're aligned
DC.W 0 ; version-0
;========================================================================================
;VideoOpen allocates private storage for the device in the DCE and locks
; it down for perpetuity. It installs the interrupt handler and enables
; the interrupts. It also sets the default gamma table included in the driver.
;
;Entry:
; A0 = param block pointer
; A1 = DCE pointer
;
;Locals:
; A2 = Saved param block pointer
; A3 = Saved DCE pointer
; A4 = Saved interrupt handler ptr
;========================================================================================
;Save registers
VideoOpen
MOVE.L A0, A2 ; A2 <- param block pointer
MOVE.L A1, A3 ; A3 <- DCE pointer
;Allocate private storage
MOVEQ #dCtlSize, D0 ; get size of parameters
_ResrvMem ,SYS ; make room as low as possible
MOVEQ #dCtlSize, D0 ; get size of parameters
_NewHandle ,SYS,CLEAR ; get some memory for private
; storage
BNE OpError ;=> return an error in open
MOVE.L A0, dCtlStorage(A3) ; saved returned handle in DCE
_HLock ; and lock it down
;Get and install the interrupt handler
LEA BeginIH, A4 ; Save point to interrupt handler
MOVEQ #SlotIntQElement.sqHDSize,D0 ; allocate a slot queue element
_NewPtr ,SYS,CLEAR ; get it from system heap cleared
BNE OpError
MOVE.W #SIQType, SlotIntQElement.sqType(A0) ; setup queue ID
MOVE.L A4, SlotIntQElement.sqAddr(A0) ; setup int routine address
MOVE.L A3, SlotIntQElement.sqParm(A0) ; save slot base addr as A3 parm
CLR.L D0
MOVE.B dctlSlot(A3), D0 ; setup slot #
_SIntInstall ; and do install
BNE.S OpError
;Save SQElPtr for removal
MOVE.L dCtlStorage(A3), A1 ; Get point to private storage
MOVE.L (A1), A1
MOVE.L A0, saveSQElPtr(A1) ; Save the SQ element pointer
;Enable interrupts
MOVE.W #1, -(A7) ; enabled
SUBQ #2, A7 ; result code
MOVE.W #kCmndVideoSetIntEnbl, -(A7)
LEA TailData, A0
MOVE.L (A0)+, -(A7)
MOVEA.L (A0), A0
MOVE.L A7, (A0)
ADDA.W #10, A7
MOVEQ #0, D0 ; no error
BRA.S EndOpen
; Error
OpError
MOVE.L #openErr, D0 ; say can't open driver
EndOpen
RTS
;========================================================================================
; The interrupt handler for the board
;========================================================================================
; On entry A1 contains DCE
; wrong! : "D0-D3/A0-A3 have been preserved."
; (comment from Apples sample code.)
; must preserve registers except A1/D0
BeginIH
MOVE.L A0, -(A7)
; clear interrupt from card
SUBQ #2, A7 ; result code
MOVE.W #kCmndVideoClearInt, -(A7)
LEA TailData, A0
MOVE.L (A0)+, -(A7)
MOVEA.L (A0), A0
MOVE.L A7, (A0)
ADDQ.W #8, A7
MOVE.L dctlDevBase(A1), D0 ; D0 = $Fsxxxxxx
ROL.L #8, D0 ; D0 <- $xxxxxxFs Convert the
; address into
AND #$0F, D0 ; D0 <- $xxxx000x the slot
; number
MOVE.L JVBLTask, A0 ; call the VBL task manager
JSR (A0) ; with slot # in D0
MOVE.L (A7)+, A0
MOVEQ #1, D0 ; signal that int was serviced
RTS ; and return to caller
;========================================================================================
;
;VideoClose releases the device's private storage.
;
;Entry:
; A0 = param block pointer
; A1 = DCE pointer
;
;Locals:
; A2 = Saved param block pointer
; A3 = Saved DCE pointer
; A4 = Temporary
;
;========================================================================================
VideoClose
MOVE.L A3, -(A7) ; save
MOVE.L dCtlStorage(A1), A3; Get pointer to private storage
MOVE.W #0, -(A7) ; disabled
SUBQ #2, A7 ; result code
MOVE.W #kCmndVideoSetIntEnbl, -(A7)
LEA TailData, A0
MOVE.L (A0)+, -(A7)
MOVEA.L (A0), A0
MOVE.L A7, (A0)
ADDA.W #10, A7
MOVE.L (A3), A0
MOVE.L saveSQElPtr(A0), A0 ; Get the SQ element pointer
_SIntRemove ; Remove the interrupt handler
MOVE.L A3, A0 ; Dispose of the private storage
_DisposHandle
MOVEQ #0, D0 ; get error into D0
MOVE.L (A7)+, A3 ; restore A3
RTS ; return to caller
;========================================================================================
;
;Video Driver Control Call Handler.
;
; Entry:
; A0 = param block pointer
; A1 = DCE pointer
; Uses:
; A2 = cs paramaters (i.e. A2 <- csParam(A0)) (must be preserved)
; A3 = scratch (doesn't need to be preserved)
; A4 = scratch (must be preserved)
; D0-D3 = scratch (don't need to be preserved)
;
; Exit: D0 = error code
;
;========================================================================================
;Decode the call
VideoCtl
MOVE.L A0, -(A7)
SUBQ #2, A7 ; result code
MOVE.W #kCmndVideoControl, -(A7)
BRA.S VideoStatusControlCommon
;========================================================================================
;
;Video DriverStatus Call Handler. Right now there are three calls:
;
; (2) GetMode
; (4) GetPage
; (5) GetPageBase
;
; Entry:
; A0 = param block
; A1 = DCE pointer
; Uses:
; A2 = cs paramaters (i.e. A2 <- csParam(A0)) (must be preserved)
; A3 = scratch (doesn't need to be preserved)
; D0-D3 = scratch (don't need to be preserved)
;
; Exit: D0 = error code
;
;========================================================================================
VideoStatus
MOVE.L A0, -(A7)
SUBQ #2, A7 ; result code
MOVE.W #kCmndVideoStatus, -(A7)
VideoStatusControlCommon
LEA TailData, A0
MOVE.L (A0)+, -(A7)
MOVEA.L (A0), A0
MOVE.L A7, (A0)
ADDA.W #6, A7
MOVE.W (A7)+, D0 ; save result code
MOVE.L (A7)+, A0 ; restore A0
;========================================================================================
; Exit from control or status
;========================================================================================
BTST #NoQueueBit,ioTrap(A0) ;no queue bit set?
BEQ.S GoIODone ;=> no, not immediate
RTS ;otherwise, it was an immediate call
GoIODone
MOVE.L JIODone,A0 ;get the IODone address
JMP (A0)
TailData
ENDP
END