ref: 21f5ac6f65245a6d5f1b63b0f1a38d4001f1d5dc
dir: /LEAF/Inc/eeprom.h/
/** ****************************************************************************** * @file EEPROM_Emulation/inc/eeprom.h * @author MCD Application Team * @brief This file contains all the functions prototypes for the EEPROM * emulation firmware library. ****************************************************************************** * @attention * * <h2><center>© Copyright (c) 2017 STMicroelectronics. * All rights reserved.</center></h2> * * This software component is licensed by ST under Ultimate Liberty license * SLA0044, the "License"; You may not use this file except in compliance with * the License. You may obtain a copy of the License at: * www.st.com/SLA0044 * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __EEPROM_H #define __EEPROM_H /* Includes ------------------------------------------------------------------*/ #include "stm32h7xx_hal.h" #include "main.h" /* Exported constants --------------------------------------------------------*/ /* EEPROM emulation firmware error codes */ #define EE_OK (uint32_t)HAL_OK #define EE_ERROR (uint32_t)HAL_ERROR #define EE_BUSY (uint32_t)HAL_BUSY #define EE_TIMEOUT (uint32_t)HAL_TIMEOUT #define FLASH_BASE_ADDR (uint32_t)(FLASH_BASE) #define FLASH_END_ADDR (uint32_t)(0x081FFFFF) /* Base address of the Flash sectors Bank 1 */ #define ADDR_FLASH_SECTOR_0_BANK1 ((uint32_t)0x08000000) /* Base @ of Sector 0, 128 Kbytes */ #define ADDR_FLASH_SECTOR_1_BANK1 ((uint32_t)0x08020000) /* Base @ of Sector 1, 128 Kbytes */ #define ADDR_FLASH_SECTOR_2_BANK1 ((uint32_t)0x08040000) /* Base @ of Sector 2, 128 Kbytes */ #define ADDR_FLASH_SECTOR_3_BANK1 ((uint32_t)0x08060000) /* Base @ of Sector 3, 128 Kbytes */ #define ADDR_FLASH_SECTOR_4_BANK1 ((uint32_t)0x08080000) /* Base @ of Sector 4, 128 Kbytes */ #define ADDR_FLASH_SECTOR_5_BANK1 ((uint32_t)0x080A0000) /* Base @ of Sector 5, 128 Kbytes */ #define ADDR_FLASH_SECTOR_6_BANK1 ((uint32_t)0x080C0000) /* Base @ of Sector 6, 128 Kbytes */ #define ADDR_FLASH_SECTOR_7_BANK1 ((uint32_t)0x080E0000) /* Base @ of Sector 7, 128 Kbytes */ /* Base address of the Flash sectors Bank 2 */ #define ADDR_FLASH_SECTOR_0_BANK2 ((uint32_t)0x08100000) /* Base @ of Sector 0, 128 Kbytes */ #define ADDR_FLASH_SECTOR_1_BANK2 ((uint32_t)0x08120000) /* Base @ of Sector 1, 128 Kbytes */ #define ADDR_FLASH_SECTOR_2_BANK2 ((uint32_t)0x08140000) /* Base @ of Sector 2, 128 Kbytes */ #define ADDR_FLASH_SECTOR_3_BANK2 ((uint32_t)0x08160000) /* Base @ of Sector 3, 128 Kbytes */ #define ADDR_FLASH_SECTOR_4_BANK2 ((uint32_t)0x08180000) /* Base @ of Sector 4, 128 Kbytes */ #define ADDR_FLASH_SECTOR_5_BANK2 ((uint32_t)0x081A0000) /* Base @ of Sector 5, 128 Kbytes */ #define ADDR_FLASH_SECTOR_6_BANK2 ((uint32_t)0x081C0000) /* Base @ of Sector 6, 128 Kbytes */ #define ADDR_FLASH_SECTOR_7_BANK2 ((uint32_t)0x081E0000) /* Base @ of Sector 7, 128 Kbytes */ /* Define the size of the sectors to be used */ #define PAGE_SIZE (uint32_t)0x20000 /* Page size = 128KByte */ /* Device voltage range supposed to be [2.7V to 3.6V], the operation will be done by word */ #define VOLTAGE_RANGE (uint8_t)VOLTAGE_RANGE_3 /* EEPROM emulation start address in Flash */ #define EEPROM_START_ADDRESS ADDR_FLASH_SECTOR_6_BANK2 /* sector6 of bank 2 */ /* Pages 0 and 1 base and end addresses */ #define PAGE0_BASE_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + 0x0000)) #define PAGE0_END_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + (PAGE_SIZE - 1))) #define PAGE0_ID FLASH_SECTOR_6 #define PAGE1_BASE_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + PAGE_SIZE)) #define PAGE1_END_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + (2 * PAGE_SIZE - 1))) #define PAGE1_ID FLASH_SECTOR_7 /* Used Flash pages for EEPROM emulation */ #define PAGE0 ((uint16_t)0x0000) #define PAGE1 ((uint16_t)0x0001) /* Page nb between PAGE0_BASE_ADDRESS & PAGE1_BASE_ADDRESS*/ /* No valid page define */ #define NO_VALID_PAGE ((uint16_t)0x00AB) /* Page status definitions */ #define ERASED ((uint16_t)0xFFFF) /* Page is empty */ #define RECEIVE_DATA ((uint16_t)0xEEEE) /* Page is marked to receive data */ #define VALID_PAGE ((uint16_t)0x0000) /* Page containing valid data */ /* Valid pages in read and write defines */ #define READ_FROM_VALID_PAGE ((uint8_t)0x00) #define WRITE_IN_VALID_PAGE ((uint8_t)0x01) /* Page full define */ #define PAGE_FULL ((uint8_t)0x80) /* Variables' number */ #define NB_OF_VAR ((uint8_t)0x03) /* Exported types ------------------------------------------------------------*/ /* Exported macro ------------------------------------------------------------*/ /* Exported functions ------------------------------------------------------- */ /* Virtual address defined by the user: 0xFFFF value is prohibited */ extern uint16_t VirtAddVarTab[NB_OF_VAR]; uint16_t EE_Init(void); uint16_t EE_ReadVariable(uint16_t VirtAddress, uint16_t* Data); uint16_t EE_WriteVariable(uint16_t VirtAddress, uint16_t Data); #endif /* __EEPROM_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/